Keri-systems EP1501 Manual de usuario descargar pdf

www.mercury-security.com

2355 MIRA MAR AVE. LONG BEACH, CA 90815-1755, (562)986-9105 FAX (562) 986-9205

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this

device must accept any interference received, including

interference that may cause undesired operation.

EP1501 Intelligent Controller

with Paired Reader Interface for One Physical Barrier

Installation and Specifications:

1. General:

The EP1501 intelligent controller provides decision making, event reporting and database storage for the

Mercury hardware platform. Two reader interfaces configured as paired or alternate readers provide

control for one physical barrier.

Host communication is via the on-board 10-BaseT/100Base-TX Ethernet port.

Note: For UL compliance, the Power Sourcing Equipment (PSE) such as a PoE enabled network switch

and/or PoE power injectors must be UL Listed under UL294B.

Reader port 1 can accommodate a reader that utilizes TTL (D1/D0, Clock/Data), F/2F, or 2-wire RS-485

device signaling, also provides tri-state LED control, and buzzer control (one wire LED mode only). This

port can also utilize multiple 2-wire RS-485 multi-dropped devices, such as up to two readers or up to

eight remote serial I/O devices.

Reader port 2 can accommodate a reader that utilizes TTL (D1/D0, Clock/Data), or F/2F signaling, also

provides tri-state LED control, and buzzer control (one wire LED mode only). Two Form-C contact relay

outputs may be used for door strike control or alarm signaling. The relay contacts are rated at 2 A @ 30

Vdc, dry contact configuration. Two inputs are provided that may be used for monitoring the door

contact, exit push button or alarm contact. Input circuits can be configured as unsupervised or

supervised. The EP1501 requires Power over Ethernet (PoE) or 12 Vdc for power. The EP1501 may be

mounted in a 3-gang switch box; a mounting plate is supplied with the unit, or may be mounted in an

enclosure; the supplied mounting plate has mounting holes that match the MR50 mounting footprint.

2. EP1501 Hardware:

TB1 TB2 TB3

1 1 1

12V

PoE

TB5

TB4

2 1

7 6 5 4 3 2 1

BT1

TB1

TB5

RESET SWITCH

.15 [3.81] 2.55 [64.77] 2.55 [64.77] .15 [3.81]

.20 [5.08]

5.40 [137.16]

2.35 [59.69]

.20 [5.08]

2.75 [69.85]

TAMPER

SWITCH

CONNECTION

(J7)

ETHERNET

CONNECTOR

(J6)

PoE/12Vdc

POWER SELECTOR

JUMPER (J3)

DIP SWITCHES

STATUS LEDs CHASSIS GND

Ø .125 [Ø3.175]

6 PL

SOLDER SIDE

RELAY K1 LED

RELAY K2 LED

1 2 3 4 5 6 ... 10 11

Indice de contenidos

Pagina 1 - 2. EP1501 Hardware:

Pagina 2 - 3. EP1501 Wiring and Setup:

Pagina 3 - 6. Communication Wiring:

Pagina 4 - DO (GREEN LED)

Pagina 5

Pagina 6 - 8. Input Circuit Wiring:

Pagina 7 - 10. Memory Backup Battery:

Pagina 8 - 12. IT Security

Pagina 9 - 13. Specifications:

Pagina 10

Pagina 11

Comentarios a estos manuales

Sin comentarios

Keri-systems EP1501 Manual de usuario

Busca en linea o descarga Manual de usuario para Sensores Keri-systems EP1501. Keri Systems EP1501 User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Keri-systems EP1501